[fpc-devel] Problems building xtensa-freertos RTL in trunk

[Michael Ring]

Just to be sure, from your Path settings it looks like you are using 
esp-idf from the release/v4.0 Branch, correct?

Michael

Am 04.04.20 um 19:44 schrieb Florian Klämpfl:
> Am 04.04.20 um 16:06 schrieb Christo Crause via fpc-devel:
>> I'm keen to test the xtensa-freertos target, but it seems there are a 
>> couple of patches missing from trunk.
>>
>> It is possible to build an xtensa cross compiler, but the make files 
>> doesn't know the xtensa-freertos target. To get the make files in 
>> rtl  updated, one needs to rebuild fpcmake, edit rtl/MakeFile.fpc and 
>> add "dirs_freertos=freertos" to the target list, then run fpcmake. At 
>> this point the the following make command proceeds up to sysutils:
>> make rtl FPC=~/fpc/3.3.1/compiler/ppcrossxtensa CPU_TARGET=xtensa 
>> OS_TARGET=freertos BINUTILSPREFIX=xtensa-esp32-elf-
>>
>> where the following errors crop up:
>> syssbh.inc(43,41) Error: Identifier not found "Double"
>> syssbh.inc(49,41) Error: Identifier not found "Single" etc.
>>
>> I trust someone (Florian...) has a working build?
>>
>
> I sent Michael recently some instructions but I am not sure if they 
> are still working. As Pierre got qemu-xtensa working I am pushing the 
> linux port so we can test more easily the compiler.
>
> - install esp-idf and execute
>   source ~/eps/esp-idf/export.sh
>   to get the pathes and environment set (namely tools path and 
> $IDF_PATH are needed)
> - use the lazarus project fpc/compiler/ppcxtens.lpt to build an xtensa 
> compiler
> - build the rtl (breaks currently at sysutils, doesn't matter):
> cd rtl/freertos
> make FPC=../../compiler/xtensa/pp  OS_TARGET=freertos "OPT=-Cplx6 
> -Cawindowed -XPxtensa-esp32-elf-" clean all
> - build the example hello world program from the esp-idf, copy all 
> generated .a into e.g. ~/xtensa-esp32-elf-libs
> - create somewhere a hello world program, compile it with
> fpc/compiler/xtensa/pp -Fu../rtl/units/xtensa-freertos/ -Tfreertos 
> -Cawindowed -XPxtensa-esp32-elf- -al -O3 -Wpesp32 
> -Fl~/xtensa-esp32-elf-libs 
> -Fl$HOME/.espressif/tools/xtensa-esp32-elf/esp-2019r2-8.2.0/xtensa-esp32-elf/xtensa-esp32-elf/lib/ 
> hello
> - get partition-table.bin and bootloader.bin from the hello_world 
> example compiled above and copy them into the same dir as the compiled 
> hello.bin
> - flash with
> esptool.py -p /dev/ttyUSB0 -b 460800 --before default_reset --after 
> hard_reset --chip esp32  write_flash --flash_mode dio --flash_size 
> detect --flash_freq 40m 0x1000 bootloader.bin 0x8000 
> partition-table.bin 0x10000 hello.bin
> - monitor the output with:
> idf_monitor.py  --port /dev/ttyUSB0 hello.elf
>
> _______________________________________________
> fpc-devel maillist  -  fpc-devel at lists.freepascal.org
> https://lists.freepascal.org/cgi-bin/mailman/listinfo/fpc-devel