[fpc-devel] Arm Thumb2 - Stellaris status

[John Clymer]

As part of my table-ization of cpuinfo.pas, I am including a generic part for 
each (no code published for this yet.)  The caveat to this is that FLASH size 
and SRAM sizes are just set to extremely large (1 MB each for now).  Which means 
if the code size exceeds the space of the device - the compiler/linker will not 
catch the overflow of the available resource.  (Running objsize on the ELF file 
will display the sizes - so I just run that after every successful compile.)

Also, still testing, but I have the "interrupt" reserved word working (more or 
less, more testing needed.)  This takes the interrupt codeword with an integer.  
The integer is the offset into the vectors table.  If no interrupt is provided 
for the given address, it defaults to DefaultHandler in the startup file - which 
is just a continual loop - so one can breakpoint on it.  (This can be enabled / 
disabled via a define in the source.)  This is should only be enabled for the 
embedded target - but I need to double check to ensure that is the case.

Fortunately, I have a few days off before the school semester starts - so I will 
be working on this quite heavily over the next few days.

John







________________________________
From: Geoffrey Barton <mrb at periphon.net>
To: FPC developers' list <fpc-devel at lists.freepascal.org>
Sent: Sun, August 21, 2011 6:01:22 PM
Subject: Re: [fpc-devel] Arm Thumb2 - Stellaris status


On 20 Aug 2011, at 15:46, David Welch wrote:

>> 
>> 
>> The great strength of ARM is that the peripherals, even if in different 
>>locations in different manufacturers parts, are identical in hardware terms if 
>>they are all cortex m3; that is the IP which they license from ARM.com. So maybe 
>>that is another reason for keeping the peripheral offset definitions and 
>>peripheral drivers separate and out of the compiler.
>> 
>> Geoffrey
>> 
>> 
> 
> Not sure what you are saying here, almost none of the peripherals are the same 
>from vendor to vendor.  With the cortex-m3 the systick timer and the VNIC for 
>example are from ARM, sure, but the majority of the items you are going to use 
>timers, dma, pwm, gpio, clocks and enables, etc are vendor specific and vastly 
>different from vendor to vendor. Within a vendor they are very similar if not 
>the same but from ti to st most of the items are not compatible, likewise from 
>ti to lpc/nxp or ti to atmel, etc.

You are right, of course. I have not looked at the data for other than Stellaris 
devices, I just generalised from the ARM TRM.

> 
> Normally these are libraries and not buried in the compiler proper, I agree 
>with that.  Perhaps that is what you were saying and I misunderstood.

not quite, but it is my aspiration :-)

> 
> And as with libraries you can take them or leave them, that would want to be 
>the case here (without having to dig into the compiler proper). Would need to 
>roll your own target to avoid/modify a library.  Ideally with the compiler you 
>want to specify the arm core to take advantages of instructions each newer core 
>supports.  Not use them to tie to boards or systems.
> 
> I was hoping for thumb support but I now see that the choices are limited to 
>arm and thumb+thumb2 (without any separation between thumb and thumb2).  
>Actually thumb2 wasnt working for me, I got an arm+thumb2 mix, so I will ride 
>this along for a while and see what comes up, otherwise limit my use to ARM 
>targets, or start working on a thumb backend.  Adding backends as well as arm 
>embedded are of interest to me so I may work on a little of both.
> 
> So far it seems to be very straight forward to add a platform/device to fpc arm 
>embedded, so if the stock support is too bulky or confusing individuals can 
>cherry pick items they want and make their own simpler target.

The approach used in coide is quite interesting. Have a look on coocox.org. They 
have it down to box ticking.

> 
> Actually what we definitely need here in the near term is an arm generic target 
>and a thumb2 generic target that does not have any of the vendor specific items 
>in it, perhaps not even core specific peripherals.

I agree.

> 
> I understand this is a work in progress and sorting everything out will take 
>some time.

Unfortunately the discussion is rather torn between the basic simplicity camp 
and the portmanteau camp. I rather think the latter is more suitable for a 
commercial company which can afford the maintenance, otherwise it is always 
out-of-date. Keeping up with new ARM cores is perhaps enough to do already.

Geoffrey.

> 
> David
> 
> _______________________________________________
> fpc-devel maillist  -  fpc-devel at lists.freepascal.org
> http://lists.freepascal.org/mailman/listinfo/fpc-devel

_______________________________________________
fpc-devel maillist  -  fpc-devel at lists.freepascal.org
http://lists.freepascal.org/mailman/listinfo/fpc-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freepascal.org/pipermail/fpc-devel/attachments/20110821/de6ab2ab/attachment.html>